Add hannoprint code

hannoprint/Marlin-2.1.2.1/config/examples/Prusa/MK3/README.md

@@ -0,0 +1,102 @@
+# Einsy Rambo Config for Průša MK3S
+
+## Requirements
+- [Průša MK3S, MK3S+, or MK3 with MK3S/MK3S+ upgrade](https://www.prusa3d.com/original-prusa-i3-mk3/) is required for filament runout to work properly.
+- Stock Einsy Rambo with integrated TMC2130s
+
+## Configuration Options
+
+Flags specific to this printer/configuration:
+
+- `MK3_FAN_PINS` - Disable this for `FAN_PIN 8` and `FAN1_PIN 6`
+- `GEARBOX_BEAR` - Is printer equipped with a 3.5:1 gearbox on the extruder?
+- `LOWBAUD` - Printer needs lower baudrate?
+- `TALLBEAR` - Tall Bear (320mm)?
+- `SUPERPINDA` - SuperPinda present?
+
+## Changes to Start G-code
+The `W` in Průša's `G28 W ; home all without mesh bed level` default G-code does not exist in Marlin and [`G80 ; mesh bed leveling`](https://marlinfw.org/docs/gcode/G080.html) cancels the current motion mode, so no bed leveling will take place.
+
+Below are some example start G-code scripts from popular slicers to get you started.
+
+### PrusaSlicer
+- Set your G-code flavor to "Marlin 2" under "Printer Settings" -> "General" -> "Firmware" -> "G-code flavor".
+- Use the "Custom G-code" section under "Filament Settings" to add the [Linear Advance](https://marlinfw.org/docs/features/lin_advance.html) (`M900 K0.0`) value since it can be saved on a per-filament basis.
+- Paste the start G-code block below in the "Custom G-code" section under "Printer Settings".
+
+```gcode
+G90 ; use absolute coordinates
+M83 ; extruder relative mode
+M104 S170 ; preheat hotend to 170
+M140 S[first_layer_bed_temperature] ; set bed temp
+M190 S[first_layer_bed_temperature] ; wait for bed temp
+G28 ; home all
+G29 ; mesh bed leveling
+G1 X0 Z0.6 Y-3.0 F1000.0 ; go outside print area for intro line
+M104 S[first_layer_temperature] ; set hotend temp
+M109 S[first_layer_temperature] ; wait for hotend temp
+G92 E0.0
+G1 X60.0 E9.0 F1000.0 ; intro line
+G1 X100.0 E12.5 F1000.0 ; intro line
+G92 E0.0
+```
+
+### Cura
+Paste the start G-code block below in the "Start G-code" section. Add your [Linear Advance](https://marlinfw.org/docs/features/lin_advance.html) (`M900 K0.0`) value in the start G-code block below:
+```gcode
+G90 ; use absolute coordinates
+M83 ; extruder relative mode
+M900 K0.0 ; place your linear advance value here
+M104 S170 ; preheat hotend to 170
+M140 S{material_bed_temperature_layer_0} ; set bed temp
+M190 S{material_bed_temperature_layer_0} ; wait for bed temp
+G28 ; home all
+G29 ; mesh bed leveling
+G1 X0 Z0.6 Y-3.0 F1000.0 ; go outside print area for intro line
+M104 S{material_print_temperature_layer_0} ; set hotend temp
+M109 S{material_print_temperature_layer_0} ; wait for hotend temp
+G92 E0.0
+G1 X60.0 E9.0 F1000.0 ; intro line
+G1 X100.0 E12.5 F1000.0 ; intro line
+G92 E0.0
+```
+
+### IdeaMaker
+Paste the start G-code block below in the filament's "Start G-code" section. Add your [Linear Advance](https://marlinfw.org/docs/features/lin_advance.html) (`M900 K0.0`) value in the start G-code block below:
+```gcode
+G90 ; use absolute coordinates
+M83 ; extruder relative mode
+M900 K0.0 ; place your linear advance value here
+M104 S170 ; preheat hotend to 170
+M140 S{temperature_heatbed} ; set bed temp
+M190 S{temperature_heatbed} ; wait for bed temp
+G28 ; home all
+G29 ; mesh bed leveling
+G1 X0 Z0.6 Y-3.0 F1000.0 ; go outside print area for intro line
+M104 S{temperature_extruder1} ; set hotend temp
+M109 S{temperature_extruder1} ; wait for hotend temp
+G92 E0.0
+G1 X60.0 E9.0 F1000.0 ; intro line
+G1 X100.0 E12.5 F1000.0 ; intro line
+G92 E0.0
+```
+
+### Simplify3D
+Paste the start G-code block below in the "Starting Script" section. Add your [Linear Advance](https://marlinfw.org/docs/features/lin_advance.html) (`M900 K0.0`) value in the start G-code block below:
+```gcode
+G90 ; use absolute coordinates
+M83 ; extruder relative mode
+M900 K0.0 ; place your linear advance value here
+M104 S170 ; preheat hotend to 170
+M140 S[bed0_temperature] ; set bed temp
+M190 S[bed0_temperature] ; wait for bed temp
+G28 ; home all
+G29 ; mesh bed leveling
+G1 X0 Z0.6 Y-3.0 F1000.0 ; go outside print area for intro line
+M104 S[extruder0_temperature] T0 ; set hotend temp
+M109 S[extruder0_temperature] T0 ; wait for hotend temp
+G92 E0.0
+G1 X60.0 E9.0 F1000.0 ; intro line
+G1 X100.0 E12.5 F1000.0 ; intro line
+G92 E0.0
+```

hannoprint/Marlin-2.1.2.1/config/examples/Prusa/MK3S-BigTreeTech-BTT002/README.md

@@ -0,0 +1,108 @@
+# BigTreeTech BTT002/TMC2209 Config for Průša MK3S
+
+## Requirements
+- [Průša MK3S, MK3S+, or MK3 with MK3S/MK3S+ upgrade](https://www.prusa3d.com/original-prusa-i3-mk3/) is required for filament runout to work properly.
+- BigTreeTech BTT002 motherboard
+- 4 x BigTreeTech TMC2209s (DIAG pin location differs from Watterott's & similar designs)
+
+## Configuration Options
+
+Flags specific to this printer/configuration:
+
+- `MK3_FAN_PINS` - Disable this for `FAN_PIN PB9` and `FAN1_PIN PB8`
+- `GEARBOX_BEAR` - Is printer equipped with a 3.5:1 gearbox on the extruder?
+- `TALLBEAR` - Tall Bear (320mm)?
+- `SUPERPINDA` - SuperPinda present?
+
+## Upgrade Notes
+* ⚠️ Cut or desolder the Z & E driver DIAG pins or they will interfere with PINDA & filament runout detection. ⚠️
+* Set the jumpers under your drivers to "TMC2208-UART MODE":
+
+  <img src="https://user-images.githubusercontent.com/13375512/74117621-24415000-4b6d-11ea-8811-f867e187ea0c.png" width="50%">
+
+## Changes to Start G-code
+The `W` in Průša's `G28 W ; home all without mesh bed level` default G-code does not exist in Marlin and [`G80 ; mesh bed leveling`](https://marlinfw.org/docs/gcode/G080.html) cancels the current motion mode, so no bed leveling will take place.
+
+Below are some example start G-code scripts from popular slicers to get you started.
+
+### PrusaSlicer
+- Set your G-code flavor to "Marlin 2" under "Printer Settings" -> "General" -> "Firmware" -> "G-code flavor".
+- Use the "Custom G-code" section under "Filament Settings" to add the [Linear Advance](https://marlinfw.org/docs/features/lin_advance.html) (`M900 K0.0`) value since it can be saved on a per-filament basis.
+- Paste the start G-code block below in the "Custom G-code" section under "Printer Settings".
+
+```gcode
+G90 ; use absolute coordinates
+M83 ; extruder relative mode
+M104 S170 ; preheat hotend to 170
+M140 S[first_layer_bed_temperature] ; set bed temp
+M190 S[first_layer_bed_temperature] ; wait for bed temp
+G28 ; home all
+G29 ; mesh bed leveling
+G1 X0 Z0.6 Y-3.0 F1000.0 ; go outside print area for intro line
+M104 S[first_layer_temperature] ; set hotend temp
+M109 S[first_layer_temperature] ; wait for hotend temp
+G92 E0.0
+G1 X60.0 E9.0 F1000.0 ; intro line
+G1 X100.0 E12.5 F1000.0 ; intro line
+G92 E0.0
+```
+
+### Cura
+Paste the start G-code block below in the "Start G-code" section. Add your [Linear Advance](https://marlinfw.org/docs/features/lin_advance.html) (`M900 K0.0`) value in the start G-code block below:
+```gcode
+G90 ; use absolute coordinates
+M83 ; extruder relative mode
+M900 K0.0 ; place your linear advance value here
+M104 S170 ; preheat hotend to 170
+M140 S{material_bed_temperature_layer_0} ; set bed temp
+M190 S{material_bed_temperature_layer_0} ; wait for bed temp
+G28 ; home all
+G29 ; mesh bed leveling
+G1 X0 Z0.6 Y-3.0 F1000.0 ; go outside print area for intro line
+M104 S{material_print_temperature_layer_0} ; set hotend temp
+M109 S{material_print_temperature_layer_0} ; wait for hotend temp
+G92 E0.0
+G1 X60.0 E9.0 F1000.0 ; intro line
+G1 X100.0 E12.5 F1000.0 ; intro line
+G92 E0.0
+```
+
+### IdeaMaker
+Paste the start G-code block below in the filament's "Start G-code" section. Add your [Linear Advance](https://marlinfw.org/docs/features/lin_advance.html) (`M900 K0.0`) value in the start G-code block below:
+```gcode
+G90 ; use absolute coordinates
+M83 ; extruder relative mode
+M900 K0.0 ; place your linear advance value here
+M104 S170 ; preheat hotend to 170
+M140 S{temperature_heatbed} ; set bed temp
+M190 S{temperature_heatbed} ; wait for bed temp
+G28 ; home all
+G29 ; mesh bed leveling
+G1 X0 Z0.6 Y-3.0 F1000.0 ; go outside print area for intro line
+M104 S{temperature_extruder1} ; set hotend temp
+M109 S{temperature_extruder1} ; wait for hotend temp
+G92 E0.0
+G1 X60.0 E9.0 F1000.0 ; intro line
+G1 X100.0 E12.5 F1000.0 ; intro line
+G92 E0.0
+```
+
+### Simplify3D
+Paste the start G-code block below in the "Starting Script" section. Add your [Linear Advance](https://marlinfw.org/docs/features/lin_advance.html) (`M900 K0.0`) value in the start G-code block below:
+```gcode
+G90 ; use absolute coordinates
+M83 ; extruder relative mode
+M900 K0.0 ; place your linear advance value here
+M104 S170 ; preheat hotend to 170
+M140 S[bed0_temperature] ; set bed temp
+M190 S[bed0_temperature] ; wait for bed temp
+G28 ; home all
+G29 ; mesh bed leveling
+G1 X0 Z0.6 Y-3.0 F1000.0 ; go outside print area for intro line
+M104 S[extruder0_temperature] T0 ; set hotend temp
+M109 S[extruder0_temperature] T0 ; wait for hotend temp
+G92 E0.0
+G1 X60.0 E9.0 F1000.0 ; intro line
+G1 X100.0 E12.5 F1000.0 ; intro line
+G92 E0.0
+```